Alkali-activated composites with synthetic fibers and recycled aggregates: a study of mechanical properties
DOI:
https://doi.org/10.54355/tbus/4.2.2024.0058Keywords:
alkali-activated composites, metazeolite, synthetic fibers, environmental standards, recycled concrete aggregateAbstract
This study examines the potential for enhancing alkali-activated composites (AACs) through the incorporation of a blend of meta-zeolite (MZ) and slag, reinforced with synthetic fibers and incorporating aluminum sludge (AS) and recycled concrete aggregate. AACs were activated with sodium hydroxide (NaOH) and sodium silicate (Na₂SiO₃) in varying ratios and molarities (8M to 14M). The optimal mix, comprising 50% MZ and 50% S at 12M NaOH with 30% AS, exhibited notable enhancements in mechanical properties. Specifically, the addition of 0.5% basalt fibers resulted in a 7.26% increase in compressive strength and a 24.15% enhancement in flexural strength. These findings underscore the potential of MZ-S-based AACs, enhanced with aluminum sludge and basalt fiber, to develop advanced, sustainable construction materials. The study underscores the significance of optimizing material ratios and reinforcement strategies to achieve superior performance, thereby contributing to the development of environmentally friendly building solutions that align with contemporary standards.
Downloads
Metrics
References
A. M. Lakew et al., “Combined effect of using steel fibers and demolition waste aggregates on the performance of fly ash/slag based geopolymer concrete,” European Journal of Environmental and Civil Engineering, vol. 27, no. 15, pp. 4251–4278, Nov. 2023, doi: 10.1080/19648189.2023.2189468. DOI: https://doi.org/10.1080/19648189.2023.2189468
C. Demirel and O. Şimşek, “Erken Yaşdaki Atık Betonların Geri Dönüşüm Agregası Olarak Beton Üretiminde Kullanılabilirliği ve Sürdürülebilirlik Açısından İncelenmesi,” Düzce Üniversitesi Bilim ve Teknoloji Dergisi, vol. 3, no. 1, pp. 226–235, 2015.
F. Sahin, M. Uysal, O. Canpolat, T. Cosgun, and H. Dehghanpour, “The effect of polyvinyl fibers on metakaolin-based geopolymer mortars with different aggregate filling,” Constr Build Mater, vol. 300, p. 124257, Sep. 2021, doi: 10.1016/j.conbuildmat.2021.124257. DOI: https://doi.org/10.1016/j.conbuildmat.2021.124257
X. Zheng, J. Zhang, X. Ding, H. Chu, and J. Zhang, “Frost resistance of internal curing concrete with calcined natural zeolite particles,” Constr Build Mater, vol. 288, p. 123062, Jun. 2021, doi: 10.1016/j.conbuildmat.2021.123062. DOI: https://doi.org/10.1016/j.conbuildmat.2021.123062
C. Florez, O. Restrepo-Baena, and J. I. Tobon, “Effects of calcination and milling pre-treatments on natural zeolites as a supplementary cementitious material,” Constr Build Mater, vol. 310, p. 125220, Dec. 2021, doi: 10.1016/j.conbuildmat.2021.125220. DOI: https://doi.org/10.1016/j.conbuildmat.2021.125220
A. Nikolov, H. Nugteren, and I. Rostovsky, “Optimization of geopolymers based on natural zeolite clinoptilolite by calcination and use of aluminate activators,” Constr Build Mater, vol. 243, p. 118257, May 2020, doi: 10.1016/j.conbuildmat.2020.118257. DOI: https://doi.org/10.1016/j.conbuildmat.2020.118257
S. Özen and B. Alam, “Compressive Strength and Microstructural Characteristics of Natural Zeolite-based Geopolymer,” Periodica Polytechnica Civil Engineering, Jun. 2017, doi: 10.3311/PPci.10848. DOI: https://doi.org/10.3311/PPci.10848
Y. Aygörmez, “Performance of ambient and freezing-thawing cured metazeolite and slag based geopolymer composites against elevated temperatures,” Revista de la construcción, vol. 20, no. 1, pp. 145–162, 2021, doi: 10.7764/RDLC.20.1.145. DOI: https://doi.org/10.7764/RDLC.20.1.145
R. R. Bellum, “Influence of steel and PP fibers on mechanical and microstructural properties of fly ash-GGBFS based geopolymer composites,” Ceram Int, vol. 48, no. 5, pp. 6808–6818, Mar. 2022, doi: 10.1016/j.ceramint.2021.11.232. DOI: https://doi.org/10.1016/j.ceramint.2021.11.232
O. A. Abdulkareem and J. C. Matthews, “Improving the Mechanical Strengths of Hybrid Waste Geopolymer Binders by Short Fiber Reinforcement,” Arab J Sci Eng, vol. 46, no. 5, pp. 4781–4789, May 2021, doi: 10.1007/s13369-020-05170-6. DOI: https://doi.org/10.1007/s13369-020-05170-6
Y. Alrefaei and J.-G. Dai, “Tensile behavior and microstructure of hybrid fiber ambient cured one-part engineered geopolymer composites,” Constr Build Mater, vol. 184, pp. 419–431, Sep. 2018, doi: 10.1016/j.conbuildmat.2018.07.012. DOI: https://doi.org/10.1016/j.conbuildmat.2018.07.012
F. Amalia, N. Akifah, Nurfadilla, and Subaer, “Development of Coconut Trunk Fiber Geopolymer Hybrid Composite for Structural Engineering Materials,” IOP Conf Ser Mater Sci Eng, vol. 180, p. 012014, Mar. 2017, doi: 10.1088/1757-899X/180/1/012014. DOI: https://doi.org/10.1088/1757-899X/180/1/012014
K. Arunkumar, M. Muthukannan, A. Sureshkumar, A. Chithambarganesh, and R. K. D. R, “Mechanical and durability characterization of hybrid fibre reinforced green geopolymer concrete,” Research on Engineering Structures and Materials, vol. 8, no. 1, pp. 19–43, 2021, doi: 10.17515/resm2021.280ma1604. DOI: https://doi.org/10.17515/resm2021.280ma1604
P. Nuaklong et al., “Enhancement of mechanical properties of fly ash geopolymer containing fine recycled concrete aggregate with micro carbon fiber,” Journal of Building Engineering, vol. 41, p. 102403, Sep. 2021, doi: 10.1016/j.jobe.2021.102403. DOI: https://doi.org/10.1016/j.jobe.2021.102403
W. Punurai, W. Kroehong, A. Saptamongkol, and P. Chindaprasirt, “Mechanical properties, microstructure and drying shrinkage of hybrid fly ash-basalt fiber geopolymer paste,” Constr Build Mater, vol. 186, pp. 62–70, Oct. 2018, doi: 10.1016/j.conbuildmat.2018.07.115. DOI: https://doi.org/10.1016/j.conbuildmat.2018.07.115
W. H. Sachet and W. D. Salman, “Compressive Strength Development of Slag-Based Geopolymer Paste Reinforced with Fibers Cured at Ambient Condition,” IOP Conf Ser Mater Sci Eng, vol. 928, no. 2, p. 022117, Nov. 2020, doi: 10.1088/1757-899X/928/2/022117. DOI: https://doi.org/10.1088/1757-899X/928/2/022117
K. Zada Farhan, M. Azmi Megat Johari, and R. Demirboğa, “Evaluation of properties of steel fiber reinforced GGBFS-based geopolymer composites in aggressive environments,” Constr Build Mater, vol. 345, p. 128339, Aug. 2022, doi: 10.1016/j.conbuildmat.2022.128339. DOI: https://doi.org/10.1016/j.conbuildmat.2022.128339
M. Frydrych et al., “Impact of Flax and Basalt Fibre Reinforcement on Selected Properties of Geopolymer Composites,” Sustainability, vol. 12, no. 1, p. 118, Dec. 2019, doi: 10.3390/su12010118. DOI: https://doi.org/10.3390/su12010118
X. Gao, Q. L. Yu, R. Yu, and H. J. H. Brouwers, “Evaluation of hybrid steel fiber reinforcement in high performance geopolymer composites,” Mater Struct, vol. 50, no. 2, p. 165, Apr. 2017, doi: 10.1617/s11527-017-1030-x. DOI: https://doi.org/10.1617/s11527-017-1030-x
S. Guler and Z. F. Akbulut, “Effect of high-temperature on the behavior of single and hybrid glass and basalt fiber added geopolymer cement mortars,” Journal of Building Engineering, vol. 57, p. 104809, Oct. 2022, doi: 10.1016/j.jobe.2022.104809. DOI: https://doi.org/10.1016/j.jobe.2022.104809
C. H. Le, P. Louda, K. Ewa Buczkowska, and I. Dufkova, “Investigation on Flexural Behavior of Geopolymer-Based Carbon Textile/Basalt Fiber Hybrid Composite,” Polymers (Basel), vol. 13, no. 5, p. 751, Feb. 2021, doi: 10.3390/polym13050751. DOI: https://doi.org/10.3390/polym13050751
V. Sathish Kumar, N. Ganesan, and P. V. Indira, “Effect of Hybrid Fibres on the Durability Characteristics of Ternary Blend Geopolymer Concrete,” Journal of Composites Science, vol. 5, no. 10, p. 279, Oct. 2021, doi: 10.3390/jcs5100279. DOI: https://doi.org/10.3390/jcs5100279
A. Baziak, K. Pławecka, I. Hager, A. Castel, and K. Korniejenko, “Development and Characterization of Lightweight Geopolymer Composite Reinforced with Hybrid Carbon and Steel Fibers,” Materials, vol. 14, no. 19, p. 5741, Oct. 2021, doi: 10.3390/ma14195741. DOI: https://doi.org/10.3390/ma14195741
A. Chithambar Ganesh and M. Muthukannan, “Experimental Study on the Behaviour of Hybrid Fiber Reinforced Geopolymer Concrete under Ambient Curing Condition,” IOP Conf Ser Mater Sci Eng, vol. 561, p. 012014, Nov. 2019, doi: 10.1088/1757-899X/561/1/012014. DOI: https://doi.org/10.1088/1757-899X/561/1/012014
D. Jia, P. He, M. Wang, and S. Yan, “Short SiC Fiber and Hybrid SiC/Carbon Fiber Reinforced Geopolymer Matrix Composites,” 2020, pp. 243–270. doi: 10.1007/978-981-15-9536-3_7. DOI: https://doi.org/10.1007/978-981-15-9536-3_7
J. Junior, A. K. Saha, P. K. Sarker, and A. Pramanik, “Workability and Flexural Properties of Fibre-Reinforced Geopolymer Using Different Mono and Hybrid Fibres,” Materials, vol. 14, no. 16, p. 4447, Aug. 2021, doi: 10.3390/ma14164447. DOI: https://doi.org/10.3390/ma14164447
M. M. Maras, “Tensile and flexural strength cracking behavior of geopolymer composite reinforced with hybrid fibers,” Arabian Journal of Geosciences, vol. 14, no. 22, p. 2258, Nov. 2021, doi: 10.1007/s12517-021-08579-x. DOI: https://doi.org/10.1007/s12517-021-08579-x
P. Sukontasukkul, P. Pongsopha, P. Chindaprasirt, and S. Songpiriyakij, “Flexural performance and toughness of hybrid steel and polypropylene fibre reinforced geopolymer,” Constr Build Mater, vol. 161, pp. 37–44, Feb. 2018, doi: 10.1016/j.conbuildmat.2017.11.122. DOI: https://doi.org/10.1016/j.conbuildmat.2017.11.122
N. P. Asrani et al., “A feasibility of enhancing the impact resistance of hybrid fibrous geopolymer composites: Experiments and modelling,” Constr Build Mater, vol. 203, pp. 56–68, Apr. 2019, doi: 10.1016/j.conbuildmat.2019.01.072. DOI: https://doi.org/10.1016/j.conbuildmat.2019.01.072
J.-I. Choi, H. H. Nguyễn, S.-E. Park, R. Ranade, and B. Y. Lee, “Effects of fiber hybridization on mechanical properties and autogenous healing of alkali-activated slag-based composites,” Constr Build Mater, vol. 310, p. 125280, Dec. 2021, doi: 10.1016/j.conbuildmat.2021.125280. DOI: https://doi.org/10.1016/j.conbuildmat.2021.125280
F. U. A. Shaikh, “Tensile and flexural behaviour of recycled polyethylene terephthalate (PET) fibre reinforced geopolymer composites,” Constr Build Mater, vol. 245, p. 118438, Jun. 2020, doi: 10.1016/j.conbuildmat.2020.118438. DOI: https://doi.org/10.1016/j.conbuildmat.2020.118438
A. B. Malkawi, M. F. Nuruddin, A. Fauzi, H. Almattarneh, and B. S. Mohammed, “Effects of Alkaline Solution on Properties of the HCFA Geopolymer Mortars,” Procedia Eng, vol. 148, pp. 710–717, 2016, doi: 10.1016/j.proeng.2016.06.581. DOI: https://doi.org/10.1016/j.proeng.2016.06.581
R. Chaithanya, C. Reddy, L. Reddy, and K. Kumar, “Effect Of Molarity On Strength Characteristics Of Geopolymer Mortar Based On Fly ash and GGBS,” Solid State Technology, vol. 63, no. 2s, pp. 7847–7856, 2021.
S. Singh, M. U. Aswath, and R. V. Ranganath, “Performance assessment of bricks and prisms: Red mud based geopolymer composite,” Journal of Building Engineering, vol. 32, p. 101462, Nov. 2020, doi: 10.1016/j.jobe.2020.101462. DOI: https://doi.org/10.1016/j.jobe.2020.101462
M. Mudgal, A. Singh, R. K. Chouhan, A. Acharya, and A. K. Srivastava, “Fly ash red mud geopolymer with improved mechanical strength,” Clean Eng Technol, vol. 4, p. 100215, Oct. 2021, doi: 10.1016/j.clet.2021.100215. DOI: https://doi.org/10.1016/j.clet.2021.100215
Y. Aygörmez, “Assessment of performance of metabentonite and metazeolite-based geopolymers with fly ash sand replacement,” Constr Build Mater, vol. 302, p. 124423, Oct. 2021, doi: 10.1016/j.conbuildmat.2021.124423. DOI: https://doi.org/10.1016/j.conbuildmat.2021.124423
Y. Aygörmez, “Evaluation of the red mud and quartz sand on reinforced metazeolite-based geopolymer composites,” Journal of Building Engineering, vol. 43, p. 102528, Nov. 2021, doi: 10.1016/j.jobe.2021.102528. DOI: https://doi.org/10.1016/j.jobe.2021.102528
U. Zakira, K. Zheng, N. Xie, and B. Birgisson, “Development of high-strength geopolymers from red mud and blast furnace slag,” J Clean Prod, vol. 383, p. 135439, Jan. 2023, doi: 10.1016/j.jclepro.2022.135439. DOI: https://doi.org/10.1016/j.jclepro.2022.135439
M. Uysal, Ö. Faruk Kuranlı, Y. Aygörmez, O. Canpolat, and T. Çoşgun, “The effect of various fibers on the red mud additive sustainable geopolymer composites,” Constr Build Mater, vol. 363, p. 129864, Jan. 2023, doi: 10.1016/j.conbuildmat.2022.129864. DOI: https://doi.org/10.1016/j.conbuildmat.2022.129864
T. Alomayri and I. M. Low, “Synthesis and characterization of mechanical properties in cotton fiber-reinforced geopolymer composites,” Journal of Asian Ceramic Societies, vol. 1, no. 1, pp. 30–34, Mar. 2013, doi: 10.1016/j.jascer.2013.01.002. DOI: https://doi.org/10.1016/j.jascer.2013.01.002
T. Alomayri, F. U. A. Shaikh, and I. M. Low, “Characterisation of cotton fibre-reinforced geopolymer composites,” Compos B Eng, vol. 50, pp. 1–6, Jul. 2013, doi: 10.1016/j.compositesb.2013.01.013. DOI: https://doi.org/10.1016/j.compositesb.2013.01.013
H. Baykara, M. H. Cornejo, A. Espinoza, E. García, and N. Ulloa, “Preparation, characterization, and evaluation of compressive strength of polypropylene fiber reinforced geopolymer mortars,” Heliyon, vol. 6, no. 4, p. e03755, Apr. 2020, doi: 10.1016/j.heliyon.2020.e03755. DOI: https://doi.org/10.1016/j.heliyon.2020.e03755
Downloads
Published
How to Cite
License
Copyright (c) 2024 Ramazan Cingi, Bolat Balapanov, Mucteba Uysal, Beyza Fahriye Aygun, Sarsenbek Montayev, Orhan Canpolat
![Creative Commons License](http://i.creativecommons.org/l/by-nc/4.0/88x31.png)
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
Funding data
-
Türkiye Bilimsel ve Teknolojik Araştırma Kurumu
Grant numbers Project number: 123M288